Machine edge medium speed pulverizer

Machine edge medium speed pulverizer
Performance advantages
1, the Department of the product to optimize the size of the product to a minimum, saving the site, and the bottom with pulleys, mobile convenience.
2, widely used: This model crush recovery PU, PET, PC, ABS and other soft and hard material outlet material.
3, easy to split design, color change material easy and easy, small and less space, suitable for small workshop room use.
4, there are hopper type and automatic recycling type to choose from. Hopper type, the machine comes with the bottom of the hopper, loading crushed after the completion of the material; automatic recovery type, the machine has a matching recovery system, you can crush the material directly into the injection molding machine to continue recycling.
5, because such models speed is low, so when used to produce low noise.
6, the speed of the machine side crusher is mainly used to place in the plastic molding machine next to the robot with the nozzle material will be crushed into granular, and then by the immediate recovery device will be sent back to the plastic molding machine recycling again.
7, equipped with motor overload and power supply chain and safety switches and other protection systems, and equipped with card machine alarm system, easy to operate and safe.
8, a unique tool holder design, high-quality tool (tool material Cr12MVo) preparation, so the powder particles evenly, less powder.
The difference between the machine side middle speed pulverizer and the power grinder
Power crusher advantages and disadvantages: knife shaft speed fast, the impact of crushing with the cutting tool cutting, for most of the plastic, rubber, Chinese herbal medicines, wood products, such as a good smashing effect. And the grinding power from small to large selection range, minicomputer can be used for machine edge smash and install the immediate recovery device, saving manpower and material and turnaround time. Mainframe can achieve centralized crushing, high yield, can also be configured large-scale recovery bagging fan, smash at the same time, the crushed material blowing through the fan to the storage bucket. Compared with the slow crusher, strong crusher noise, crushed after the particles as slow crusher evenly.
Slow mute the advantages and disadvantages: slow speed, teeth bite-type crushing, uniform particles, no screen, easy cleaning and disassembly can be configured immediately recovery device to achieve the proportion of crushed material and raw materials recovery. Noise is small, idling noise value of about 20DB. Mostly used for machine edge crushing, compared with the strong crusher, slow crusher only for hard plastic crushing, and smashing power is relatively small, the cost is relatively high. Machine edge medium speed pulverizer use
         The medium-speed crusher is specially used for the recycling of various plastic materials, including plastic scrap, back material, semi-finished products, suitable for soft chlorine, polycarbonate, nylon, ABS and other hard and soft type plastic, plastic. The machine is compact, handsome in appearance, easy to operate, turn the knife to optimize the design to minimize energy consumption, higher cutting efficiency.
Save time: 30 seconds immediately recovery, do not have to wait for the concentration of crushing, and indeed clean, clean;
Improve the quality: the outlet material will be exposed to high temperature after oxidation, humidification (absorption of water) and destruction of physical properties, 30 seconds immediately to reduce the physical strength can be reduced to reduce the destruction of color luster;
Save money: short-term recovery, to avoid pollution, mixed caused by the non-performing rate, can reduce the plastic, labor, management, storage, purchase capital waste and loss;
Uses: suitable for crushing recovery PU, PVC, PC, ABC and other soft and hard material nozzle material;
Simple: easy to split design, color change material easy and easy, small and less space, suitable for small workshop next to the use of the machine; optional automatic recovery system or powder separation system to fully avoid the waste of human materials to achieve the best Recovery effect.
Using medium speed motor, low noise, low energy consumption;
Stainless steel into the hopper design, easy to clean, do not pollute the raw materials;
Motor with overload protection device, and a power supply chain protection system, safe and reliable operation and cleaning;
Machine edge medium speed pulverizer
The machine side of the medium-speed crusher placed in the injection molding machine side smashing water and material recycling, greatly reducing the production costs, while the nozzle material, scrap recycling, to achieve environmental protection; if the re-configuration recovery device, with the manipulator operation, do not need Manual to operate, while saving labor costs.
Machine edge medium speed pulverizer

The machine is used in the injection molding machine edge, crushing the injection molding machine in the injection process of plastic scrap, scrap, outlet material, semi-finished products and other materials, the crushed particles through the recovery system, mixed with the raw materials in proportion use.

Machine edge medium speed pulverizer

型號Model	DAT-220	DAT-270A	DAT-270B	DAT-330
粉碎功率（Kw）Grinding power	1.5	1.5	2.2	4
風機功率（W）Motor power	550	550	550	550
送料方式Feeting way	風車 By windmill	風車 By windmill	風車 By windmill	風車 By windmill或吸料機配比例閥
碎料室（mm）Grinding chamber	220×210	270×230	270×230	330*230
回收能力（g/10s）Reclaim capactity，刀具數量	12KG，動刀4片，定刀2片	15KG，動刀4片，定刀2片	18KG，動刀4片，定刀2片	25KG，動刀18片，定刀2片
外形尺寸（mm）Appearance size	900×450×1100	900×500×1100	1100×500×1200	1100×600×1300
重量（Kg）Weight	115	170	250	270